Implementación de un sensor para la detección y cuantificación de h2s en gases de pirolisis de llanta
dc.contributor.advisor | Nabarlatz, Débora Álcida | |
dc.contributor.advisor | Maradei García, María Paola | |
dc.contributor.author | Rodríguez Abaunza, Cesar Augusto | |
dc.contributor.author | Rumbo Arias, Jamel Eduardo | |
dc.date.accessioned | 2024-03-03T22:10:23Z | |
dc.date.available | 2015 | |
dc.date.available | 2024-03-03T22:10:23Z | |
dc.date.created | 2015 | |
dc.date.issued | 2015 | |
dc.description.abstract | El objetivo de este proyecto era Implementar un sensor de detección de H2S que permitiera la cuantificación de este gas en las corrientes gaseosas generadas en el proceso de pirólisis de llanta usada; para esto se tuvieron en cuenta dos tipos de sensores, infrarrojo y electroquímico. Lo que se hizo con estos sensores fue una validación que se llevó a cabo a través de una reacción química entre FeS y HCl para la producción del H2S, que para el caso del sensor infrarrojo, proveniente de la universidad de los Andes, no arrojo resultados coherentes, y posterior se validó el sensor electroquímico, con el fin de analizar su comportamiento y comprobar su eficacia, la calibración se realizó atreves de el CDT de Gas de la Universidad Industrial de Santander, con botellas patrones estandarizadas. Con los resultados obtenidos en el CDT se construyó una curva de calibración de voltaje contra concentración de H2S y de acuerdo a el comportamiento de estas gráficas, se pudo comprobar que los resultados que arroja el sensor electroquímico si son coherentes y por lo tanto se pude utilizar para implementarlo en el proceso de pirólisis de llanta usada y puede llegar a ser una herramienta de control muy efectiva para ayudar a reducir impactos ambientales. | |
dc.description.abstractenglish | The objective of this project was Implement H2S detection sensor that allows the quantification of this gas in the gas streams generated in the pyrolysis of used tire; for this two types of sensors, infrared and electrochemical taken into account. What was done with these sensors was a validation that was performed through a chemical reaction between FeS and HCl for the production of H2S, which in the case of infrared sensor, from the University of the Andes, I do not throw results consistent, and later the electrochemical sensor was validated, in order to analyze their behavior and verify their effectiveness, calibration is performed dare CDT Gas Industrial University of Santander, with bottles standardized patterns. With the results of the CDT a calibration curve voltage built against concentration of H2S and according to the behavior of these graphs, it was found that the results shown by the electrochemical sensor if they are consistent and therefore I could use to implement it in the process of pyrolysis of used tire and can become a very effective tool of control to help reduce environmental impacts. | |
dc.description.degreelevel | Pregrado | |
dc.description.degreename | Ingeniero Químico | |
dc.format.mimetype | application/pdf | |
dc.identifier.instname | Universidad Industrial de Santander | |
dc.identifier.reponame | Universidad Industrial de Santander | |
dc.identifier.repourl | https://noesis.uis.edu.co | |
dc.identifier.uri | https://noesis.uis.edu.co/handle/20.500.14071/33014 | |
dc.language.iso | spa | |
dc.publisher | Universidad Industrial de Santander | |
dc.publisher.faculty | Facultad de Ingenierías Fisicoquímicas | |
dc.publisher.program | Ingeniería Química | |
dc.publisher.school | Escuela de Ingeniería Química | |
dc.rights | http://creativecommons.org/licenses/by/4.0/ | |
dc.rights.accessrights | info:eu-repo/semantics/openAccess | |
dc.rights.creativecommons | Atribución-NoComercial-SinDerivadas 4.0 Internacional (CC BY-NC-ND 4.0) | |
dc.rights.license | Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) | |
dc.rights.uri | http://creativecommons.org/licenses/by-nc/4.0 | |
dc.subject | Sensor | |
dc.subject | Ácido Sulfhídrico | |
dc.subject | Pirólisis | |
dc.subject | Calibración | |
dc.subject | Validación | |
dc.subject | Arduino | |
dc.subject | Concentraciones H2S. | |
dc.subject.keyword | Sensor | |
dc.subject.keyword | Hydrogen Sulfide | |
dc.subject.keyword | Pyrolysis | |
dc.subject.keyword | Calibration | |
dc.subject.keyword | Validation | |
dc.subject.keyword | Arduino | |
dc.subject.keyword | H2S Concentrations. | |
dc.title | Implementación de un sensor para la detección y cuantificación de h2s en gases de pirolisis de llanta | |
dc.title.english | Implementation of a sensor for detection and quantification of pyrolysis gases h2s in tire | |
dc.type.coar | http://purl.org/coar/version/c_b1a7d7d4d402bcce | |
dc.type.hasversion | http://purl.org/coar/resource_type/c_7a1f | |
dc.type.local | Tesis/Trabajo de grado - Monografía - Pregrado |
Files
Original bundle
1 - 3 of 3
No Thumbnail Available
- Name:
- Carta de autorización.pdf
- Size:
- 175.61 KB
- Format:
- Adobe Portable Document Format
No Thumbnail Available
- Name:
- Nota de proyecto.pdf
- Size:
- 88.09 KB
- Format:
- Adobe Portable Document Format